Description

Original auger for Moulinex meat grinder | MS-651328

The MS-651328 auger is the beating heart of the Moulinex meat grinder.
It is responsible for pushing the meat forward towards the knife and the mesh.
When the auger is worn or broken, grinding stops, the meat gets stuck, and the motor works harder than usual.
An original auger returns the grinder to its peak performance.

Thousands of customers have already solved this problem with one part

The certified technicians of the official service encounter this problem very frequently,
Because the snail is the component most exposed to wear in the meat grinder.
Customers who purchased this part praised the speed of simple installation and immediate return to operation.
Using an original auger ensures the device's integrity over the years, as it was designed for complete precision along with the other components of the grinder.
A non-original part may damage the blade, net, and motor due to size mismatch.
Click the “Check Model Compatibility” button at the top of the page before ordering.

✅ Original Moulinex snail, manufacturer approved

✅ Material resistant to repeated abrasion

✅ Suitable for assembly and complete disassembly for cleaning

✅ Ensures uniform feeding of the meat towards the grid

⚠️ It is important to verify exact compatibility with your model before ordering, as Moulinex produces several versions of the snail in different sizes for different device series.

What causes a snail to go bad?

The auger wears out as a result of frequent use, grinding meat with small bones, or working without sufficient product oil.
Additionally, prolonged continuous grinding places a strain on the component. As a result, the following symptoms appear:

• The meat comes out in large, uneven pieces.
• The grinder makes increased noise during grinding.
• The flesh gets stuck inside the body and does not move forward.
• The engine heats up faster than usual.

Where do you find the model number of the grinder?

You will find the model number on the front or top of the grinder body.
Sometimes the sticker is on the bottom of the device. The model number is essential to verify the compatibility of the snail before ordering.

📋 Technical specifications

✅ Compatible models

The part fits the following models (make sure it matches the model number on the sticker):

• ME546810/6R0 (MEAT GRINDER HV7 PRO)
• ME548810/6R0 (MEAT GRINDER HV7 PRO)

To check exact compatibility for your model, click the “Check Model Compatibility” button at the top of the page.

🔧 Installation instructions

⚠️ Disconnect the grinder from the power supply before starting the replacement.

1. Turn the front locking ring counterclockwise and remove it.
2. Remove the mesh and knife from the grinder body.
3. Gently pull the old snail out of the body.
4. Insert the new auger with its pin aligned with the slot in the motor body.
5. Put the knife and the net back in place.
6. Turn the locking ring clockwise until you feel it lock.
7. Connect to electricity and test operation with a little meat.

Estimated time: 5 minutes. You don't need any special tools.

💡 Tip from the experts

To extend the life of the snail, avoid grinding pieces with large bones and hard tendon tissue.
Additionally, after each use, completely disassemble the body and wash all components.
Remove excess water before storing, as moisture accelerates the erosion process.

❓ Frequently Asked Questions

Why isn't the meat grinder grinding properly?

The most common reasons are: a worn auger that is not feeding the meat properly, a dull knife, a clogged mesh, or meat that is not cold enough.
When the meat is lukewarm, it becomes less firm and is compressed instead of ground.
Cooling the meat before grinding and checking the integrity of the snail solves most problems.

What is a snail in a meat grinder?

The auger, also called an auger, is the spiral screw that pushes the meat out of the grinder body towards the knife and mesh.
It receives the rotational motion from the engine through the transmission mechanism. The integrity of the auger determines the grinding rate and the uniformity of the product.

Can I put the meat grinder parts in the dishwasher?

Moulinex grinding components, including the auger, can usually be washed in the top compartment of the dishwasher at a low temperature.
However, it is recommended to check the manufacturer's instructions for your specific model. Hand washing extends the life of the components.

How long does a snail last in a meat grinder?

The original Moulinex snail is durable for many years of reasonable use.
Intensive daily use, grinding meat with bones, and wet storage are the main causes of premature wear.
Replacing with an original part ensures the best longevity.

Why does the meat grinder make a loud noise?

A loud noise or change in the sound of the motor often indicates a worn auger, foreign sulfur that has entered the grinding body, or a clogged mesh.
Before ordering a part, it is recommended to disassemble the body and check for any stuck meat. If the noise persists after cleaning, the auger likely needs to be replaced.

⏱️ Delivery times:

• Most localities: within 10 business days
• Golan Heights, Arava, Eilat and settlements beyond the Green Line: within 10 business days