Description

Original drawer front for Bloomberg bottom freezer refrigerator | 4393710800

⚠️ Just before ordering – safety above all!

To ensure a successful repair and maintain the longevity of the device, It is mandatory to use only original parts..
Non-original parts may damage the airtight closure of the drawer and impair freezing efficiency.
Now click the 'Check Model Compatibility' button at the top of the page. And our system will immediately confirm that the part is suitable for your refrigerator.

Why did the drawer front break?

From our many years of experience in Bloomberg's official service laboratories, The front of the freezer drawer is one of the most common areas of damage..
The clear plastic is constantly exposed to freezing temperatures, and over time it may become more brittle.
Frequent opening and closing of the drawer, especially when it is loaded, increases the pressure on the front and can cause cracks or complete breakage.

Our certified technicians note that many customers contact us after noticing one of the following problems:

• ✅ Crack or break in the drawer front
• ✅ A front that was completely broken and fell out of the drawer
• ✅ Difficulty closing the drawer tightly
• ✅ Broken latches that don't hold the front in place
• ✅ Unaesthetic appearance of the internal freezer

Why an original Bloomberg drawer front?

The original Blomberg part is significantly superior to non-approved replacements.
And there are several key reasons behind this recommendation.

Perfect fit for the latch system

The original front is manufactured with maximum precision and connects seamlessly to the freezer drawer latch system in KND series models.
This perfect fit ensures a tight seal. Which prevents warm air from entering the freezer and maintains the optimal freezing temperature.

Material resistant to extreme temperatures

The transparent plastic of the original facade undergoes strict quality tests by the manufacturer and is designed to withstand temperatures down to minus 25 degrees Celsius.
Non-original materials may fall apart or break. Prolonged exposure to extreme cold.

Maintaining energy efficiency

A drawer that does not close hermetically makes the compressor work harder.
Installing an original facade restores full tightness And helps maintain the refrigerator's normal power consumption.

How do you replace the drawer front?

Replacing the freezer drawer front is a simple operation that can be done at home without special tools..
Here are the main steps:

1. Remove the drawer from the freezer. and turned it upside down
2. Release the latches. that hold the old facade – usually there are 2-4 latches
3. Remove the damaged front gently
4. Align the new front Opposite the latch holes in the drawer
5. Press gently. until you hear a locking click.
6. Put the drawer back in place. And check that it closes and opens in sections.

💡 Expert tip: Before installation, make sure the drawer and latches are free of frost or dirt that could interfere with proper connection.

How do you find the model number on a Bloomberg refrigerator?

To ensure a perfect fit, It is important to check the exact model number of your refrigerator..
On Bloomberg KND series refrigerators (bottom freezer), the model sticker is usually located in one of the following locations:

• ✅ On the inner wall of the refrigerator compartment, on the left side
• ✅ Behind the vegetable drawer (The crisper) at the bottom of the refrigerator
• ✅ At the back of the refrigerator – Technical sticker with all model details

The sticker will include the full model number (for example: KND3950) and the serial number.
With this data, you can use the compatibility check button And receive immediate confirmation that the part is exactly the right fit for your refrigerator.

Technical

Model compatibility

FAQ

Does the drawer front fit my refrigerator model?

Click the 'Check Model Compatibility' button. At the top of the page
Enter the model number from the sticker on the refrigerator, and the system will immediately confirm if the part is suitable.
The front fits Bloomberg KND3950-KND3968 series models.

Is this an original Bloomberg piece?

Yes, This is an original spare part (OEM) from the manufacturer Blomberg..
We are the official Bloomberg service in Israel and provide only original parts that have passed the manufacturer's quality control.

Can I replace the front myself?

Definitely! Installation is extremely simple and does not require special tools or technical knowledge..
The new front attaches to the drawer using plastic clips and snaps into place with a light push.
Customers who purchased this part praised the ease of installation.

How long will it take for me to receive the shipment?

Deliveries are made via a courier company and arrive Within 10 business days For most regions of the country.
To the settlements of the Golan, the Arava, Eilat and settlements beyond the Green Line – the shipment arrives Within 10 business days.
The courier will coordinate the delivery date by phone.

What if the front doesn't fit?

If you have verified compatibility using the Check Compatibility button and the part still does not fit,
The product can be returned in accordance with the transaction cancellation policy.
Contact our customer service And we will help with any questions.

This is one of the most sought after spare parts. For Bloomberg KND series refrigerators, thanks to its durability and quality of materials.
Order now and restore your freezer to perfect function and appearance!